Phone: 1 847 623-7029
Email: customfabricatingsolutions@gmail.com
Zero Clearance Fence Information
We Also Sell Universal Blanks!The Blanks come with back cuts but no holes drilled. They also come with instructions on the most efficient way to layout and drill the holes necessary for mounting the Zero Clearance Fence to your DeWalt or other brand miter saw.
The dimensions of the Zero Clearance Fence Blanks are Slider Piece One: W 1/8" x L 11-1/4" x H 6" Piece Two: W 1/8" x L 13-3/4" x H 6" Non Slider Both Pieces: W 1/8" x L 12" x H 6" |

DeWalt DW716, DHS716, DW716XPS EZ Speedy Zero Clearance Fence
1 847 623-7029
Lead Time 1 week
Exact fit for the DeWalt Model # DW716, DHS716, DW716XPS
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to setup a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.

EZ Speedy Dual Clip
Lead Time 1 week
1 847 623-7029
We've re-invented the average clipboard! The EZ Speedy Dual Clip!
This clipboard design was born out of necessity to have a clipboard that fits into the t-track on our mobile miter saw base. We took it one step further and created a clipboard that has two different geometrically bent ends. One for inserting and one for hooking. The Dual Clip also has two clips so you can utilize both sides.
Hooks to anything and the opposite side allows you to insert into our EZ Speedy Fence System or any type of strut rail system. You can even set your tablet down on the dual clip. It can even work like a sturdy writing surface. Carry with you from jobsite to jobsite.
See our product video below!

DeWalt 10" - 12" Miter Saw Zero Clearance Insert
1 847 623-7029
Lead Time 1 week
Exact fit for DeWalt Miter Saw 10" -12" Model # DW703, DW704, DW705, DW705S, DW706, DW713, DW715, DW716, DWS715, DWS716 and DHS716
Now made of High Density Polyethylene. Which makes it easy to make the initial cut and even more durable for daily commercial use.
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
- Quick measurement of desired cut. Simply hook your tape measure into the insert and easily get an initial setting with your stop.
For a higher level of accuracy, efficiency and safety, we recommend pairing our Zero Clearance Miter Saw Plastic Insert with our Zero Clearance Fence.

DeWalt Slider Saw Zero Clearance Insert (DWS780, DWS782, DWS779, DHS780 & DHS790)
1 847 623-7029
Lead Time 1 week
Exact fit for the DeWalt Model # DWS779, DWS782, DWS780, DHS780 & DHS790
Now made of High Density Polyethylene. Which makes it easy to make the initial cut and even more durable for daily commercial use.
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
- Quick measurement of desired cut. Simply hook your tape measure into the insert and easily get an initial setting with your stop.
For a higher level of accuracy, efficiency and safety, we recommend pairing our Zero Clearance Miter Saw Plastic Insert with our Zero Clearance Fence.

Bosch GCM12SD EZ Speedy Zero Clearance Fence
1 847 623-7029
Lead Time 1 week
Exact fit for the Bosch Model # GCM12SD
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to set up a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
You might be wondering why there are extra holes in the Fence & Insert that we provide...Bosch recently changed some hole locations on the latest models which forced us to add the additional holes to accommodate both early and late model saws.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or you can select a notched version below which will have the clearances needed to use your saw in the slide mode. If you have any questions or concerns, please don't hesitate to contact us! **

Hitachi, Metabo HPT C12RSH2 EZ Speedy Zero Clearance Fence
1 847 623-7029
Lead Time 1 week
Exact fit for the Hitachi, Metabo HPT Model # C12RSH2 and #C12RSH2M
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to setup a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or we can modify these with notches to clear for an additional $30. If you have any questions or concerns, please don't hesitate to contact us! *

Delta 26-2250, 26-2251 EZ Speedy Zero Clearance Fence
1 847 623-7029
Lead Time 1 week
Exact fit for the Delta Model # 26-2250,26-2251
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to set up a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or we can modify these with notches to clear for an additional $30. If you have any questions or concerns, please don't hesitate to contact us! *

DeWalt Slider EZ Speedy Zero Clearance Fence (DWS780, DWS782, DWS779, DHS780 & DHS790)
1 847 623-7029
Lead Time 1 week
Exact fit for the DeWalt Model # DWS780, DWS782, DWS779, DHS780 & DHS790
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to set up a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
Made out of 6061 Plate Aluminum with a Vinyl Protective cover.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or you can select a notched version below which will have the clearances needed to use your saw in the slide mode. If you have any questions or concerns, please don't hesitate to contact us! *

DeWalt DW718 Zero Clearance Insert
1 847 623-7029
Lead Time 1 week
Exact fit for the DeWalt Model # DW718
Now made of High Density Polyethylene. Which makes it easy to make the initial cut and even more durable for daily commercial use.
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
- Quick measurement of desired cut. Simply hook your tape measure into the insert and easily get an initial setting with your stop.
For a higher level of accuracy, efficiency and safety, we recommend pairing our Zero Clearance Miter Saw Plastic Insert with our Zero Clearance Fence.

Milwaukee 10" 2734-20, 2734-21HD EZ Speedy Zero Clearance Fence
1 847 623-7029
Lead Time 1 week
Exact fit for the Milwaukee 10" Slider Model # 2734-20, 2734-21HD
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to setup a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or we can modify these with notches to clear for an additional $30. If you have any questions or concerns, please don't hesitate to contact us! *

Milwaukee 2734-20, 2734-21HD Zero Clearance Insert
1 847 623-7029
Lead Time 1 week
Exact fit for the Milwaukee 10" Slider Model # 2734-20, 2734-21HD
The Zero Clearance Miter Saw Plastic Insert is made of PVC. Which makes it easy to make the initial cut and durable for daily commercial use.
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
- Quick measurement of desired cut. Simply hook your tape measure into the insert and easily get an initial setting with your stop.
For a higher level of accuracy, efficiency and safety, we recommend pairing our Zero Clearance Miter Saw Plastic Insert with our Zero Clearance Fence.

Makita 12" Slider EZ Speedy Zero Clearance Fence
1 847 623-7029
Lead Time 1 week
Exact fit for Model #LS1219L, LS1219LX, XSL08Z, XSL08PT
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to setup a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
Made out of 6061 Plate Aluminum with a Vinyl Protective cover.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or you can select a notched version below which will have the clearances needed to use your saw in the slide mode. If you have any questions or concerns, please don't hesitate to contact us! *