ZERO CLEARANCE FENCE for Milwaukee M18 FUEL™ 7-1/4” Dual Bevel Sliding Compound Miter Saw
This product is not yet produced. Once we have 10 customers who purchase we will proceed to prototype the saw to fulfill the orders. If by November 1, 2019 customers have not purchased, we will guarantee a 100% refund.
1 847 623-7029
Target date: November 1, 2019
Exact fit for the Milwaukee Model # 2733-20, 2733-21
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to setup a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
Made out of 6061 Plate Aluminum with a Vinyl Protective cover.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or we can modify these with notches to clear for an additional $30. If you have any questions or concerns, please don't hesitate to contact us! *
ZERO CLEARANCE TABLE INSERT for Milwaukee M18 FUEL™ 7-1/4” Dual Bevel Sliding Compound Miter Saw
This product is not yet produced. Once we have 10 customers who purchase we will proceed to prototype the saw to fulfill the orders. If by November 1, 2019 customers have not purchased, we will guarantee a 100% refund.
1 847 623-7029
Target date: November 1, 2019
Exact fit for the Milwaukee Model # 2733-20, 2733-21
The Zero Clearance Miter Saw Plastic Insert is made of PVC. Which makes it easy to make the initial cut and durable for daily commercial use.
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
- Quick measurement of desired cut. Simply hook your tape measure into the insert and easily get an initial setting with your stop.
For a higher level of accuracy, efficiency and safety, we recommend pairing our Zero Clearance Miter Saw Plastic Insert with our Zero Clearance Fence.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or we can modify these with notches to clear for an additional $30. If you have any questions or concerns, please don't hesitate to contact us! *
ZERO CLEARANCE FENCE for Metabo 10" Dual Bevel Sliding Miter Saw
This product is not yet produced. Once we have 12 customers who purchase we will proceed to prototype the saw to fulfill the orders. If by November 1, 2019 customers have not purchased, we will guarantee a 100% refund.
1 847 623-7029
Target date: November 1, 2019
Exact fit for the Metabo Model # C10FSHC, C2310DRA, C3610DRAQ4
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to setup a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
Made out of 6061 Plate Aluminum with a Vinyl Protective cover.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or we can modify these with notches to clear for an additional $30. If you have any questions or concerns, please don't hesitate to contact us! *
ZERO CLEARANCE TABLE INSERT for Metabo 10" Dual Bevel Sliding Miter Saw
This product is not yet produced. Once we have 12 customers who purchase we will proceed to prototype the saw to fulfill the orders. If by November 1, 2019 customers have not purchased, we will guarantee a 100% refund.
1 847 623-7029
Target date: November 1, 2019
Exact fit for the Metabo Model # C10FSHC, C2310DRA, C3610DRAQ4
The Zero Clearance Miter Saw Plastic Insert is made of PVC. Which makes it easy to make the initial cut and durable for daily commercial use.
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
- Quick measurement of desired cut. Simply hook your tape measure into the insert and easily get an initial setting with your stop.
For a higher level of accuracy, efficiency and safety, we recommend pairing our Zero Clearance Miter Saw Plastic Insert with our Zero Clearance Fence.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or we can modify these with notches to clear for an additional $30. If you have any questions or concerns, please don't hesitate to contact us! *
ZERO CLEARANCE FENCE for Bosch 10-in 15-Amp Dual Bevel Sliding Compound Miter Saw
This product is not yet produced. Once we have 12 customers who purchase we will proceed to prototype the saw to fulfill the orders. If by November 1, 2019 customers have not purchased, we will guarantee a 100% refund.
1 847 623-7029
Target date: November 1, 2019
Exact fit for the Bosch Model # CM10GD
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to setup a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
Made out of 6061 Plate Aluminum with a Vinyl Protective cover.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or we can modify these with notches to clear for an additional $30. If you have any questions or concerns, please don't hesitate to contact us! *
ZERO CLEARANCE TABLE INSERT for Bosch 10-in 15-Amp Dual Bevel Sliding Compound Miter Saw
This product is not yet produced. Once we have 12 customers who purchase we will proceed to prototype the saw to fulfill the orders. If by November 1, 2019 customers have not purchased, we will guarantee a 100% refund.
1 847 623-7029
Free Shipping in the USA
Target date: November 1, 2019
Exact fit for the Bosch Model # CM10GD
The Zero Clearance Miter Saw Plastic Insert is made of PVC. Which makes it easy to make the initial cut and durable for daily commercial use.
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
- Quick measurement of desired cut. Simply hook your tape measure into the insert and easily get an initial setting with your stop.
For a higher level of accuracy, efficiency and safety, we recommend pairing our Zero Clearance Miter Saw Plastic Insert with our Zero Clearance Fence.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or we can modify these with notches to clear for an additional $30. If you have any questions or concerns, please don't hesitate to contact us! *