Bosch GCM12SD Zero Clearance Table Insert
1 847 623-7029
Lead Time 1 week
Exact fit for the Bosch Model # GCM12SD
The Zero Clearance Miter Saw Plastic Insert is made of PVC. Which makes it easy to make the initial cut and durable for daily commercial use.
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
- Quick measurement of desired cut. Simply hook your tape measure into the insert and easily get an initial setting with your stop.
You might be wondering why there are extra holes in the Fence & Insert that we provide...Bosch recently changed some hole locations on the latest models which forced us to add the additional holes to accommodate both early and late model saws.
For a higher level of accuracy, efficiency and safety, we recommend pairing our Zero Clearance Miter Saw Plastic Insert with our Zero Clearance Fence.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or we can modify these with notches to clear for an additional $30. If you have any questions or concerns, please don't hesitate to contact us! *
Bosch GCM12SD EZ Speedy Zero Clearance Fence
1 847 623-7029
Lead Time 1 week
Exact fit for the Bosch Model # GCM12SD
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to set up a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
You might be wondering why there are extra holes in the Fence & Insert that we provide...Bosch recently changed some hole locations on the latest models which forced us to add the additional holes to accommodate both early and late model saws.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
Made out of 6061 Plate Aluminum with a Vinyl Protective cover.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or we can modify these with notches to clear for an additional $30. If you have any questions or concerns, please don't hesitate to contact us! *
Miter Saw to DeWalt Stand - Spacer Mounting Kit
Only a few left!
1 847 623-7029
Lead time 1 week
Now you can mount just about ANY BRAND miter saw to the DW7231 Mounting Brackets so that you can use DeWalt DWX723, DW723, DWX724 and DWX725B stand.
Fitment is for various models, but if your miter saw is not listed in the selection below, please contact us and we can see if we have something that will work!
Micro-Adjustable Flip-Away Strut Stop
847-623-7029
Made in USA
Lead time 1 week
Product details:
- Can be assembled into a left or right side
- American-made design to exceed demands of commercial manufacturing
- Clear Zinc Plating finish for corrosion resistance
- Flip-Away action and quick-set clamping for speed
- Precise indexing for accuracy
- Anti-lash spring-loaded shoulder bolts accommodate for backlash
- 1 Flat (1/6 of a turn) of the gold bolt equates to ~.010 inch
- Reliably get your adjustments down to .005" (Half a Flat)
- One full turn = 1/16"
Buy multiple and save time!
Multiple Flip-Aways will save you time by not having to break setups. Set multiple stops to different dimensions you will be required to cut.
EZ Speedy Fence System 5LR - DeWALT
Only a few left!
1 847 623-7029
Made in USA
Lead time 1 week
Includes one Flip-Away Strut Stop & one EZ Speedy Fence.
With 5 FT of material support, each EZ Speedy Fence can be assembled in either LEFT or RIGHT configuration as desired. Can be used for a variety of applications: Drill press, milling machine, chop saw, miter saw, radial arm saw, punch press, band saw.
Made for the DW723, DWX723, and DWX724 DeWalt Miter Saw Stand, our EZ Speedy Fence slides right into the T-track and quickly locks down to the stand with our patent pending EZ Speedy Mounts.
The EZ Speedy Fence has multiple points of adjustment to set the height, depth, lateral position, and angle of the EZ Speedy Fence.
Once the points of adjustment are set to your saw table, they are locked down so you can easily remove the EZ Speedy Fence from the DeWalt stand, put everything into your vehicle, and head out to the job site without losing your position.
EZ Speedy Extension
1 847 623-7029
Made in USA
Lead Time 1 week
For anyone cutting long material with our EZ Speedy Fence this EZ Speedy Extension will sure come in handy. Can be used for a variety of applications: Drill press, milling machine, chop saw, miter saw, radial arm saw, punch press, band saw.
Included with the extension:
- (1) Support Stand
- (2) Rollers
- (1) 1-5/8" x 1 5/8" x 60" Strut with proprietary holes drilled for mounting components
- (1) Mending Plate with Clamps (to attach to the EZ Speedy Fence or another Extension)
Optional EZ Speedy Quick Handle Upgrade available in the product options below!
Support Stand
Even though this Support Stand was engineered for the EZ Speedy Fence this Support Stand stands on its own.
This stand has two adjustment point, one at the bottom and one at the top. Employing our patent pending EZ Speedy Removable Tube Insert.
A hole with 1/2-13 inch thread pitch is on the top face of the hex mount for easy attachments to anything.
The hex mount slides right off when you loosen the 1/2-13 inch bolt on the side. Tighten it up to maintain rigidness.
Height Range is 32-1/4" to 39-1/2"
This stand has claw feet at its base to handle rough surfaces easily.
Average Lead Time 1 week
EZ Speedy Dual Clip
Lead Time 1 week
1 847 623-7029
We've re-invented the average clipboard! The EZ Speedy Dual Clip!
This clipboard design was born out of necessity to have a clipboard that fits into the t-track on our mobile miter saw base. We took it one step further and created a clipboard that has two different geometrically bent ends. One for inserting and one for hooking. The Dual Clip also has two clips so you can utilize both sides.
Hooks to anything and the opposite side allows you to insert into our EZ Speedy Fence System or any type of strut rail system. You can even set your tablet down on the dual clip. It can even work like a sturdy writing surface. Carry with you from jobsite to jobsite.
See our product video below!
Roller Assembly
847-623-7029
Made in the USA
This is a single spinning roller, the same one from the EZ Speedy Fence.
Purchasing this Roller will allow you to customize how many Rollers you have on your T-track Fence
Mounts to the bottom of the Rails in the EZ Speedy Fence, Extension, and Flip-Away Strut Stop
Average Lead Time 1 week
T-Track Fence: 1-5/8" x 1-5/8" x 60"
Offering the T-track we use for the EZ Speedy Fence and the EZ Speedy Extension. Buy the single T-trackto make a custom set up on one of your machines using the Flip-Away Strut Stop
Average Lead Time 1 week
Mending Plate
847-623-7029
Lead Time 1 week
Buy a single Mending Plate assembly to build a custom fence setup using our Strut Rails and Rollers. This is the same Mending Plate assembly that comes with the EZ Speedy Extension.
EZ Speedy Fence System 10LR - DeWALT
Lead time 1 week
Made in the USA
With 10FT of material support left and the right of your saw, you will have armed yourself with the best fence system money can buy. Our fence system was designed with strength & durability in mind. All steel construction. Zinc plated to resist corrosion for use in all weather conditions.
See our set up video on YouTube below of this exact system and you will see it can be set up in under 4 minutes!
Currently this will fit on the DeWalt DW723, DWX723 & DWX724 Stand.
Included with bundle:
- (2) EZ Speedy Fence
- (2) EZ Speedy Extension
- Optional Flip Stop (up to 6)
- EZ Speedy Quick Handle included for every applicable component of your order. (Fence Mounts, Mending plates, Extension Stands, Flip-Stop(s), Kickstand
- EZ Speedy Dolly (Holds 2 EZ Speedy Fences & 2 EZ Speedy Extensions)
- Optional Mobility upgrade for your Stand (Axle, Kickstand w/ Quick Handles & Roller Tip Handle)
- Optional EZ Speedy Dual Clip
Save over $60 by purchasing our system in bundles!
*Never exceed the weight capacity of your stand... our system mounts to it so this is kind of important. EZ Speedy Fence System 10LR weight is approximately 130lbs.*
EZ Speedy Quick Handle
1 847 623-7029
Lead Time 1 week
PLEASE READ CAREFULLY!
Please specify in "Order Comments" Which of the following products you would like Quick Handles for. Then look at the Total Required and enter that quantity when adding the Quick Handle to your cart!
- EZ Speedy Fence (Qty 1) 1 ¾”, (Qty 2) 1 ½” (Total Required: Qty 3)
- EZ Speedy Extension (Qty 1) 1 ¼”, (Qty 2) 1 ½” (Total Required: Qty 3)
- Mending Plate (Qty 2) 1 ½” (Total Required: Qty 2)
- Micro-Adjustable Flip Away Strut Stop (Qty 1) 1 ¾” (Total Required: Qty 1)
- EZ Speedy Crown Stop (Qty 4) 2 ¼”, (Qty 2) 1 ½” (New Product coming soon!)
- EZ Speedy Crown Clamp (Qty 2) 2 ¼ & (Qty 4) 1 ¼ (New Product coming soon!)
- EZ Speedy Horizontal Hold Down (Qty 1) 1 ¼”, (Qty 2) 2 ¼” (New Product coming soon!)
- EZ Speedy Vertical Hold Down (Qty 1) 2 ¼, (Qty 2) 1 ½” (New Product coming soon!)
- Kick Stand (Qty 2) 1 ¼” (Total Required: Qty 2)
We developed our own heavy duty version of your typical "Vise" or "C-clamp" style handle. Intended to be used to replace any 1/2 - 13 bolt on our products where applicable.
Currently in use in our own shop! Like on our "Flip Away Strut Stop", our own "EZ Speedy Fence", and our "Mending Plate" (See photos)
Benefits & Application:
The EZ Speedy Quick Handle will boost your efficiency and eliminate the need of a bolt.
Your application can become toolless.
No more struggling to find that open ended/allen wrench.
When the clamping range is limited or a specific setting is required or adjustment and can be incrementally tightened or loosened as required.
Specification:
Main Body Dimensions: 1/2" - 13 Thread, 3/4" OD x 1-1/2" L
Handle Dimensions: 1/4" - 20 Thread 3/8" OD x 3" L
Socket Set Screw: 1/2" - 13 x 2-1/4"L
High Quality Machined steel construction. All zinc plated to resist corrosion.