Universal EZ Speedy Zero Clearance Left and Right Fence Blank
Purchase 2 or more product lower shipping cost
Lead Time 1 week
Perhaps you have a saw that we don't cover in our EZ Speedy Zero Clearance Fence model lineup. We now sell universal fence blanks that you can customize for your own saw!
All that's needed is a Drill, 3/16 Drill Bit and a Countersink Bit to drill mounting holes.
Comes with instructions.
- Increase product cutting support.
- Reduce chipping.
- Reduce kickback.
- Reduced blade binding cutting small parts.
- Made from lightweight stable heat treated 6061-T6 Plate.
- Vinyl Protective Film Cover.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to set up a miter cut as quickly and accurately as a 90-degree cut.
Enter your desired fence dimensions in the boxes below. (Tolerance +/- 1/16")
Length Available = Up to 13 1/2"
Height Available= Up to 6"
*If you need fences that are greater than these parameters or require tighter tolerances, please email us and we will get back to you with a quote.
Made out of 6061 Plate Aluminum with a Vinyl Protective cover. These are made to order. Non Refundable. The two aluminum fence pieces come with flat head bolts + flange nuts.
EZ Speedy Flip-Stop with Calibrated micro position Dial
Purchase 2 or more save on shipping
847-623-7029
Made in USA
Lead time 1 week
Increase your productivity with the redesigned EZ Speedy Flip Stop! Engineered for those craftsmen who wish to take their material cutting to the next level of tolerance and accuracy. Each line on the dial is calibrated to adjust cuts +/- 0.0052". Featuring an adjustable aluminum quick handle, which can be positioned so that it doesn't interfere with anything while in use. Simply lift and reposition.
Product details:
- Can be assembled into a left or right side - flush with table, low, or high positioning.
- American-made design to exceed demands of commercial manufacturing
- Clear Zinc Plating finish for corrosion resistance
- Stop Plate Dimension 1/4" thick 2-3/4" wide 2-5/8" tall
- Flip-Away action and quick-set clamping for speed
- Multi position black powder coat aluminum locking handle.
- Precise indexing for accuracy
- 1 line (1/12 of a turn) equates to 0.0052"
- Easy, repeatability with your cuts
- One full turn = 1/16"
Purchasing one means you will receive a quantity of one!
Buy multiple and save time!
Multiple Flip-Stops will save you time by not having to break setups. Set multiple stops to different dimensions you will be required to cut.
Miter Saw to DeWalt Stand - Spacer Mounting Kit
Only a few left!
1 847 623-7029
Lead time 1 week
Mount just about ANY BRAND miter saw to the DW7231 Mounting Brackets so that you can use DeWalt DWX723, DW723, DWX724 and DWX725B stand.
Fitment is for various models, but if your miter saw is not listed in the selection below, please contact us and we can see if we have something that will work!
Hercules Miter Saw to Hercules Stand - Spacer Mounting Kit
1 847 623-7029
Lead time 1 week
Designed for mounting Hercules Miter Saw Model # HE74 to the Hercules Stand Model # HA71
We know that if you have the Hercules saw and stand that you purchase, our kit will remedy the mounting problem. The hercules miter saw has rubber feet which give the saw the ability to not stretch what your setting the saw on. They also prevent the saw from shifting or sliding in use. The problem you run into when you attempt to bolt the saw base down to the hercules mounting brackets is that the mounting brackets will bolt up crooked and you end up deforming the brackets and you will warp the saw base. Our spacer kit will allow you to mount using the included bolts included when you purchase the stand.
DeWalt 12" DW716,DW716XPS and DHS716, EZ Speedy Zero Clearance Left and Right Fence
Purchase 2 or more product lower shipping cost
Exact fit for the DeWalt Model # DW716, DW716XPS and DHS716
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping.
- Reduce kickback.
- Reduced blade binding cutting small parts.
- Made from lightweight stable heat treated 6061-T6 Plate.
- Vinyl Protective Film Cover.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to setup a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
EZ Speedy Dual Clip
Lead Time 1 week
1 847 623-7029
We've re-invented the average clipboard! The EZ Speedy Dual Clip!
This clipboard design was born out of necessity to have a clipboard that fits into the t-track on our mobile miter saw base. We took it one step further and created a clipboard that has two different geometrically bent ends. One for inserting and one for hooking. The Dual Clip also has two clips so you can utilize both sides.
Hooks to anything and the opposite side allows you to insert into our EZ Speedy Fence System or any type of strut rail system. You can even set your tablet down on the dual clip. It can even work like a sturdy writing surface. Carry with you from jobsite to jobsite.
See our product video below!
DeWalt 10" - 12" Miter Saw Zero Clearance Table Insert
Purchase 2 or more lower shipping cost
Buy 3 and get 1 Free you save 25%
Exact fit for DeWalt Miter Saw 10" -12" Model # DW703, DW704, DW705, DW705S, DW706, DW713, DW715, DW716, DWS713, DWS715, DWS716 and DHS716
Made from High Density Polyethylene . Which makes it easy to make the initial cut and even more durable for daily commercial use.
- Machined out of solid Density Polyethylene Sheet
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
- Quick measurement of desired cut. Simply hook your tape measure into the insert and easily get an initial setting with your stop.
For a higher level of accuracy, efficiency and safety, we recommend pairing our Zero Clearance Miter Saw Plastic Insert with our Zero Clearance Fence.
DeWalt 12" (DWS780, DWS782, DWS779, DHS780 & DHS790) Zero Clearance Table Insert
Purchase 2 or more lower shipping cost
Buy 3 and get 1 Free you save 25%
1 847 623-7029
Exact fit for the DeWalt Model # DWS779, DWS782, DWS780, DHS780 & DHS790
Made from High Density Polyethylene. Which makes it easy to make the initial cut and even more durable for daily commercial use.
- Machined out of solid Density Polyethylene Sheet
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
- Quick measurement of desired cut. Simply hook your tape measure into the insert and easily get an initial setting with your stop.
For a higher level of accuracy, efficiency and safety, we recommend pairing our Zero Clearance Miter Saw Plastic Insert with our Zero Clearance Fence.
Bosch 12" GCM12SD and 12GDCN14 EZ Speedy Zero Clearance Left and Right Fence
Purchase 2 or more product lower shipping cost
Exact fit for the Bosch Model # GCM12SD and 12GDCN14
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts
- Made from lightweight stable heat treated 6061-T6 plate
- Vinyl protective film cover
Standard fence configuration has the right fence clearance for blade gear housing when cutting right 45-degree miters.
We also mil a 45 degree back cut on the inside blade edges of the aluminum fences. This will allow you to change the miter angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to set up a miter cut as quickly and accurately as a 90-degree cut.
The left and right aluminum fences come with mounting hardware.
You must select old model or new model to obtain specific mounting hole locations.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or you can select a notched version below which will have the clearances needed to use your saw in the slide mode. If you have any questions or concerns, please don't hesitate to contact us! **
Hitachi 12" Metabo HPT C12RSH2 EZ Speedy Zero Clearance Left and Right Fence
Purchase 2 or more product lower shipping cost
Exact fit for the Hitachi, Metabo HPT Model # C12RSH2 and #C12RSH2M
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- New 6" tall fence cutting support.
- Reduce chipping.
- Reduce kickback.
- Reduced blade binding cutting small parts.
- Made from lightweight stable heat treated 6061-T6 Plate.
- Vinyl Protective Film Cover.
Right Fence has been machined for clearance of blade gear housing when cutting right 45-degree miters.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to setup a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or you can select a notched version below which will have the clearances needed to use your saw in the slide mode. If you have any questions or concerns, please don't hesitate to contact us! *
Delta Cruzer 12" 26-2250, 26-2251 EZ Speedy Zero Clearance Left and Right Fence
Purchase 2 or more product lower shipping cost
Exact fit for the Delta Cruzer 12" Model # 26-2250,26-2251
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping.
- Reduce kickback.
- Reduced blade binding cutting small parts.
- Made from lightweight stable heat treated 6061-T6 Plate.
- Vinyl Protective Film Cover.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to set up a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or we can modify these with notches to clear for an additional $30. If you have any questions or concerns, please don't hesitate to contact us! *
DeWalt 12" DWS780, DWS782, DWS779, DHS780 & DHS790 EZ-Speedy Zero Clearance Left and Right Fence
Purchase 2 or more product lower shipping cost
NEW DESIGN
Exact fit for the DeWalt Model # DWS780, DWS782, DWS779, DHS780 & DHS790
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping.
- Reduce kickback.
- Reduced blade binding cutting small parts.
- Made from lightweight stable heat treated 6061-T6 Plate.
- Vinyl Protective film cover.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to set up a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or you can select a notched version below which will have the clearances needed to use your saw in the slide mode. If you have any questions or concerns, please don't hesitate to contact us! *
DeWalt 12" DW718 Zero Clearance Table Insert
Purchase 2 or more lower shipping cost
Buy 3 and get 1 Free you save 25%
Exact fit for the DeWalt 12" Model # DW718
Made from High Density Polyethylene. Which makes it easy to make the initial cut and even more durable for daily commercial use.
- Machined out of solid Density Polyethylene Sheet
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
- Quick measurement of desired cut. Simply hook your tape measure into the insert and easily get an initial setting with your stop.
For a higher level of accuracy, efficiency and safety, we recommend pairing our Zero Clearance Miter Saw Plastic Insert with our Zero Clearance Fence.