- Product Store
- >
- EZ Speedy Fence System
- >
- Roller Curb
Roller Curb
Worried about your material falling off the rollers? Maybe you've positioned your EZ Speedy Fence System on a hill and you want to prevent you material from sliding off the roller. Well that's why we created the Roller Curb!
Simply pull the plastic cap off your existing roller, and insert the Roller Curb. Tighten the center bolt to clamp to the inside of the roller and your ready to go!
*Roller NOT included - comes as pictured (Image 1-2)*
On Sale
On Sale
DeWalt 12" DW716,DW716XPS and DHS716, EZ Speedy Zero Clearance Left and Right Fence
Purchase 2 or more product lower shipping cost
Exact fit for the DeWalt Model # DW716, DW716XPS and DHS716
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping.
- Reduce kickback.
- Reduced blade binding cutting small parts.
- Made from lightweight stable heat treated 6061-T6 Plate.
- Vinyl Protective Film Cover.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to setup a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
On Sale
On Sale
Bosch 12" GCM12SD and 12GDCN14 EZ Speedy Zero Clearance Left and Right Fence
Purchase 2 or more product lower shipping cost
Exact fit for the Bosch Model # GCM12SD and 12GDCN14
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts
- Made from lightweight stable heat treated 6061-T6 plate
- Vinyl protective film cover
Standard fence configuration has the right fence clearance for blade gear housing when cutting right 45-degree miters.
We also mil a 45 degree back cut on the inside blade edges of the aluminum fences. This will allow you to change the miter angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to set up a miter cut as quickly and accurately as a 90-degree cut.
The left and right aluminum fences come with mounting hardware.
You must select old model or new model to obtain specific mounting hole locations.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or you can select a notched version below which will have the clearances needed to use your saw in the slide mode. If you have any questions or concerns, please don't hesitate to contact us! **
On Sale
On Sale
Hitachi 12" Metabo HPT C12RSH2 EZ Speedy Zero Clearance Left and Right Fence
Purchase 2 or more product lower shipping cost
Exact fit for the Hitachi, Metabo HPT Model # C12RSH2 and #C12RSH2M
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- New 6" tall fence cutting support.
- Reduce chipping.
- Reduce kickback.
- Reduced blade binding cutting small parts.
- Made from lightweight stable heat treated 6061-T6 Plate.
- Vinyl Protective Film Cover.
Right Fence has been machined for clearance of blade gear housing when cutting right 45-degree miters.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to setup a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or you can select a notched version below which will have the clearances needed to use your saw in the slide mode. If you have any questions or concerns, please don't hesitate to contact us! *
On Sale
On Sale
Delta Cruzer 12" 26-2250, 26-2251 EZ Speedy Zero Clearance Left and Right Fence
Purchase 2 or more product lower shipping cost
Exact fit for the Delta Cruzer 12" Model # 26-2250,26-2251
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping.
- Reduce kickback.
- Reduced blade binding cutting small parts.
- Made from lightweight stable heat treated 6061-T6 Plate.
- Vinyl Protective Film Cover.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to set up a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or we can modify these with notches to clear for an additional $30. If you have any questions or concerns, please don't hesitate to contact us! *
On Sale
On Sale
DeWalt 12" DWS780, DWS782, DWS779, DHS780 & DHS790 EZ-Speedy Zero Clearance Left and Right Fence
Purchase 2 or more product lower shipping cost
NEW DESIGN
Exact fit for the DeWalt Model # DWS780, DWS782, DWS779, DHS780 & DHS790
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping.
- Reduce kickback.
- Reduced blade binding cutting small parts.
- Made from lightweight stable heat treated 6061-T6 Plate.
- Vinyl Protective film cover.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to set up a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or you can select a notched version below which will have the clearances needed to use your saw in the slide mode. If you have any questions or concerns, please don't hesitate to contact us! *
On Sale
On Sale
Milwaukee 10" 2734-20, 2734-21HD EZ Speedy Zero Clearance Left and Right Fence
Purchase 2 or more product lower shipping cost
Exact fit for the Milwaukee 10" Slider Model # 2734-20, 2734-21HD
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping.
- Reduce kickback.
- Reduced blade binding cutting small parts.
- Made from lightweight stable heat treated 6061-T6 Plate.
- Vinyl Protective Film Cover.
Right Fence clearance for motor housing when cutting right 45 degree miters
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to setup a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or we can modify these with notches to clear for an additional $30. If you have any questions or concerns, please don't hesitate to contact us! *
On Sale
On Sale
Makita 12" LS1219L, LS1219LX, XSL08Z, XSL08PT, GSL04Z. LS003GZ and DLS211Z EZ Speedy Zero Clearance Left and Right Fence
Purchase 2 or more product lower shipping cost
Exact fit for Model #LS1219L, LS1219LX, XSL08Z, XSL08PT, GSL04Z, LS003GZ and DLS211Z
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping.
- Reduce kickback.
- Reduced blade binding cutting small parts.
- Made from lightweight stable heat treated 6061-T6 Plate.
- Vinyl Protective Film Cover.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to setup a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or you can select a notched version below which will have the clearances needed to use your saw in the slide mode. If you have any questions or concerns, please don't hesitate to contact us! *
On Sale
On Sale
Makita 10" LS1019L, LS1019LX, XSL04PTU, XSL04ZU, XSL06PT, XSL06Zand GSL03Z EZ Speedy Zero Clearance Left and Right Fence
Purchase 2 or more product lower shipping cost
Exact fit for Makita Model #LS1019L, LS1019LX, XSL04PTU, XSL04ZU, XSL06PT, XSL06Z and GSL03Z
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping.
- Reduce kickback.
- Reduced blade binding cutting small parts.
- Made from lightweight stable heat treated 6061-T6 Plate.
- Vinyl Protective Film Cover.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to setup a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or you can select a notched version below which will have the clearances needed to use your saw in the slide mode. If you have any questions or concerns, please don't hesitate to contact us! *
On Sale
On Sale
DeWalt 12" DW708 EZ Speedy Zero Clearance Left and Right Fence
Purchase 2 or more product lower shipping cost
Exact fit for the DeWalt Model # DW708
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping.
- Reduce kickback.
- Reduced blade binding cutting small parts.
- Made from lightweight stable heat treated 6061-T6 Plate.
- Vinyl Protective Film Cover.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to set up a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or you can select a notched version below which will have the clearances needed to use your saw in the slide mode. If you have any questions or concerns, please don't hesitate to contact us! *
On Sale
On Sale
Hitachi 12" C12RSH EZ Speedy Zero Clearance Left and Right Fence
Purchase 2 or more product lower shipping cost
Exact fit for the Hitachi Model # C12RSH
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping.
- Reduce kickback.
- Reduced blade binding cutting small parts.
- Made from lightweight stable heat treated 6061-T6 Plate.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to setup a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or we can modify these with notches to clear for an additional $30. If you have any questions or concerns, please don't hesitate to contact us! *
On Sale
On Sale
Festool KAPEX KS 120 EB & KS 120 REB EZ Speedy Zero Clearance Left and Right Fence
Purchase 2 or more product lower shipping cost
Exact fit for the Sliding Compound Miter Saw KS 120 EB & KS 120 REB
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping.
- Reduce kickback.
- Reduced blade binding cutting small parts.
- Made from lightweight stable heat treated 6061-T6 Plate.
- Vinyl Protective Film Cover.
Right Fence has been machined for clearance of blade gear housing when cutting right 45-degree miters.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to setup a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or you can select a notched version below which will have the clearances needed to use your saw in the slide mode. If you have any questions or concerns, please don't hesitate to contact us! *
On Sale
On Sale
Delta Cruzer 10" 26-2240, 26-2241 and 26-2310 EZ Speedy Zero Clearance Left and Right Fence
Purchase 2 or more product lower shipping cost
Exact fit for the Delta Cruzer 10" Model # 26-2240, 26-2241 and 26-2310
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping.
- Reduce kickback.
- Reduced blade binding cutting small parts.
- Made from lightweight stable heat treated 6061-T6 Plate.
- Vinyl Protective Film Cover.
Right Fence has been machined for clearance of blade gear housing when cutting right 45-degree miters.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to set up a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or you can select a notched version below which will have the clearances needed to use your saw in the slide mode. If you have any questions or concerns, please don't hesitate to contact us! *