- Product Store
- >
- EZ Speedy Zero Clearance Fences
- >
- DeWalt 12" DWS780, DWS782, DWS779, DHS780 & DHS790 EZ-Speedy Zero Clearance Left and Right Fence
DeWalt 12" DWS780, DWS782, DWS779, DHS780 & DHS790 EZ-Speedy Zero Clearance Left and Right Fence
Purchase 2 or more product lower shipping cost
Exact fit for the DeWalt 12" DWS780, DWS782, DWS779, DHS780 & DHS790
Extra Tall Miter Saw Fences to cut very large Crown and very tail Baseboard.
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping.
- Reduce kickback.
- Reduced blade binding cutting small parts.
- Made from lightweight stable heat treated 6061-T6 Plate.
- Vinyl Protective Film Cover.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to setup a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
On Sale
On Sale
DeWalt 12" DWS780, DWS782, DWS779, DHS780 & DHS790 EZ-Speedy Zero Clearance Left and Right Fence
Purchase 2 or more product lower shipping cost
NEW DESIGN
Exact fit for the DeWalt Model # DWS780, DWS782, DWS779, DHS780 & DHS790
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping.
- Reduce kickback.
- Reduced blade binding cutting small parts.
- Made from lightweight stable heat treated 6061-T6 Plate.
- Vinyl Protective film cover.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to set up a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or you can select a notched version below which will have the clearances needed to use your saw in the slide mode. If you have any questions or concerns, please don't hesitate to contact us! *
On Sale
On Sale
DeWalt Slider EZ Speedy Zero Clearance Bevel Fence (DWS780, DWS782, DWS779, DHS780 & DHS790)
Purchase 2 or more product lower shipping cost
Exact fit for the DeWalt Model # DWS780, DWS782, DWS779, DHS780 & DHS790
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping.
- Reduce kickback.
- Reduced blade binding cutting small parts.
- Made from lightweight stable heat treated 6061-T6 Plate.
- Vinyl Protective Film Cover.
Right Fence has been machined for clearance of blade gear housing when cutting right 45-degree bevels.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Bevel Fence with our Zero Clearance Table Insert.
On Sale
On Sale
DeWalt 12" (DWS780, DWS782, DWS779, DHS780 & DHS790) Zero Clearance Table Insert
Purchase 2 or more lower shipping cost
Buy 3 and get 1 Free you save 25%
1 847 623-7029
Exact fit for the DeWalt Model # DWS779, DWS782, DWS780, DHS780 & DHS790
Made from High Density Polyethylene. Which makes it easy to make the initial cut and even more durable for daily commercial use.
- Machined out of solid Density Polyethylene Sheet
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
- Quick measurement of desired cut. Simply hook your tape measure into the insert and easily get an initial setting with your stop.
For a higher level of accuracy, efficiency and safety, we recommend pairing our Zero Clearance Miter Saw Plastic Insert with our Zero Clearance Fence.