DEWALT 60V 12'' DCS781B, DCS781X1 Sliding Miter Saw Zero Clearance Table Insert
Purchase 2 or more lower shipping cost
Buy 3 and get 1 Free you save 25%
1 847 623-7029
Exact fit for the DEWALT 60V 12'' DCS781B, DCS781X1 Sliding Miter
Made from High Density Polyethylene. Which makes it easy to make the initial cut and even more durable for daily commercial use.
- Machined out of solid Density Polyethylene Sheet
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
- Quick measurement of desired cut. Simply hook your tape measure into the insert and easily get an initial setting with your stop.
For a higher level of accuracy, efficiency and safety, we recommend pairing our Zero Clearance Miter Saw Plastic Insert with our Zero Clearance Fence.
EZ-SPEEDY ZERO CLEARANCE TABLE INSERT REPLACEMENT HARDWARE HOLD DOWN SCREWS for model number DEWALT 60V 12'' DCS781B, DCS781X1
1 847 623-7029
Lead Time 1 week
EZ-SPEEDY ZERO CLEARANCE TABLE INSERT REPLACEMENT HARDWARE HOLD DOWN SCREWS for model number DEWALT 60V 12'' DCS781B, DCS781X1
DEWALT 60V 12'' DCS781B, DCS781X1 Sliding Miter Saw EZ-Speedy Zero Clearance Left and Right Fence
Purchase 2 or more product lower shipping cost
Exact fit for the DEWALT 60V 12'' DCS781B, DCS781X1 Sliding Miter Saw
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping.
- Reduce kickback.
- Reduced blade binding cutting small parts.
- Made from lightweight stable heat treated 6061-T6 Plate.
- Vinyl Protective film cover.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to set up a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or you can select a notched version below which will have the clearances needed to use your saw in the slide mode. If you have any questions or concerns, please don't hesitate to contact us! *
EZ Speedy New Low Support Fence System 5' - DEWALT LEFT or RIGHT
1 847 623-7029
Made in USA
Lead Time (Made to order upon request)
Includes only (1) Side
What you get is (1) EZ Speedy Flip-Stop , (1) EZ Speedy T-Track, (1) EZ-Speedy Table (2) EZ Speedy Low Coupler Mount Assemblies and (1) Pair of EZ Speedy Fence Mount with Multi position black aluminum locking handles.
With 5 FT of material support, each EZ Speedy Low Fence can be assembled in either LEFT or RIGHT configuration as desired. Can be used for a variety of applications: Drill press, milling machine, cold saw, miter saw, radial arm saw, punch press and band saw.
This support fence system and flip stop is for the DW723, DWX723, and DWX724 DEWALT Miter Saw Stand, our EZ Speedy Fence slides right into the T-track and quickly locks down to the stand with our patent EZ Speedy Mounts.
The EZ Speedy Low Fence has multiple points of adjustment to set the height, depth, lateral position, and angle of the EZ Speedy Fence.
Once the points of adjustment are set to your saw table, they are locked down so you can easily remove the EZ Speedy Fence from the DEWALT stand, put everything into your vehicle, and head out to the job site without losing your position.
EZ Speedy Dual Clip
Lead Time 1 week
1 847 623-7029
We've re-invented the average clipboard! The EZ Speedy Dual Clip!
This clipboard design was born out of necessity to have a clipboard that fits into the t-track on our mobile miter saw base. We took it one step further and created a clipboard that has two different geometrically bent ends. One for inserting and one for hooking. The Dual Clip also has two clips so you can utilize both sides.
Hooks to anything and the opposite side allows you to insert into our EZ Speedy Fence System or any type of strut rail system. You can even set your tablet down on the dual clip. It can even work like a sturdy writing surface. Carry with you from jobsite to jobsite.
See our product video below!
EZ Speedy Flip-Stop with Calibrated micro position Dial
Purchase 2 or more save on shipping
Buy 3 Get 1 Free
847-623-7029
Made in USA
Increase your productivity with the redesigned EZ Speedy Flip Stop! Engineered for those craftsmen who wish to take their material cutting to the next level of tolerance and accuracy. Each line on the dial is calibrated to adjust cuts +/- 0.0052". Featuring an adjustable aluminum quick handle, which can be positioned so that it doesn't interfere with anything while in use. Simply lift and reposition.
Product details:
- Can be assembled into a left or right side - flush with table, low, or high positioning.
- American-made design to exceed demands of commercial manufacturing
- Clear Zinc Plating finish for corrosion resistance
- Stop Plate Dimension 1/4" thick 2-3/4" wide 2-5/8" tall
- Flip-Away action and quick-set clamping for speed
- Multi position black powder coat aluminum locking handle.
- Precise indexing for accuracy
- 1 line (1/12 of a turn) equates to 0.0052"
- Easy, repeatability with your cuts
- One full turn = 1/16"
Purchasing one means you will receive a quantity of one!
Buy multiple and save time!
Multiple Flip-Stops will save you time by not having to break setups. Set multiple stops to different dimensions you will be required to cut.
EZ Speedy New Low Support Fence System 5LR - Bosch T4B and GTA3800 5' LEFT or RIGHT
1 847 623-7029
Made in USA
Lead Time (Made to order upon request)
Includes only (1) Side
What you get is (1) EZ Speedy Flip-Stop , (1) EZ Speedy T-Track, (1) EZ-Speedy Table (2) EZ Speedy Low Coupler Mount Assemblies and (1) Pair of EZ Speedy Fence Mount with Multi position black aluminum locking handles.
With 5 FT of material support, each EZ Speedy Low Fence can be assembled in either LEFT or RIGHT configuration as desired. Can be used for a variety of applications: Drill press, milling machine, cold saw, miter saw, radial arm saw, punch press and band saw.
This support fence system and flip stop is for the Bosch T4B and GTA38005' Miter Saw Stand, our EZ Speedy Fence slides right into the T-track and quickly locks down to the stand with our patent EZ Speedy Mounts.
The EZ Speedy Low Fence has multiple points of adjustment to set the height, depth, lateral position, and angle of the EZ Speedy Fence.
Once the points of adjustment are set to your saw table, they are locked down so you can easily remove the EZ Speedy Fence from the Bosch T4B and GTA38005' stand, put everything into your vehicle, and head out to the job site without losing your position.