- Product Store
- >
- Saw Stand Accessories
- >
- EZ-SPEEDY SPACER BAR KIT FOR MAKITA AND Festool KAPEX
EZ-SPEEDY SPACER BAR KIT FOR MAKITA AND Festool KAPEX
1 847 623-7029
Lead time 1 week
Miter Saw to DeWalt Stand - Spacer Mounting Kit
https://www.customfabricatingsolutions.com/store/p192/Miter_Saw_to_DeWalt_Stand_-_Spacer_Mounting_Kit.html
Designed for mounting Your Makita and Festool Kapex forward on the DeWalt DW723, DWX723 and DWX724 miter saw stand to bring the saw more in balance to the center of the miter saw stand.
Model saw that kit fit
Makita 12" and 10” LS1219L, LS1219LX, XSL08Z, XSL08PT, GSL04Z. LS003GZ and DLS211Z
LS1019L, LS1019LX, XSL04PTU, XSL04ZU, XSL06PT, XSL06Zand GSL03Z
Festool KAPEX KS 120 EB & KS 120 REB
Miter Saw to DEWALT Stand - Spacer Mounting Kit and EZ-Speedy Zero-Clearance
On Sale
On Sale
Miter Saw to DeWalt Stand - Spacer Mounting Kit
1 847 623-7029
Lead time 1 week
Mount just about ANY BRAND miter saw to the DW7231 Mounting Brackets so that you can use DeWalt DWX723, DW723, DWX724 and DWX725B stand.
Fitment is for various models, but if your miter saw is not listed in the selection below, please contact us and we can see if we have something that will work!
On Sale
On Sale
Festool KAPEX KS 120 EB & KS 120 REB Zero Clearance Table Insert
Purchase 2 or more lower shipping cost
Buy 3 and get 1 Free you save 25%
Exact fit for Festool KAPEX KS 120 EB & KS 120 REB
Made from Density Polyethylene. Which makes it easy to make the initial cut and even more durable for daily commercial use.
- Machined out of solid Density Polyethylene Sheet
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
- Quick measurement of desired cut. Simply hook your tape measure into the insert and easily get an initial setting with your stop.
For a higher level of accuracy, efficiency and safety, we recommend pairing our Zero Clearance Miter Saw Plastic Insert with our Zero Clearance Fence.
On Sale
On Sale
Festool KAPEX KS 120 EB & KS 120 REB EZ Speedy Zero Clearance Left and Right Fence
Purchase 2 or more product lower shipping cost
Exact fit for the Sliding Compound Miter Saw KS 120 EB & KS 120 REB
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping.
- Reduce kickback.
- Reduced blade binding cutting small parts.
- Made from lightweight stable heat treated 6061-T6 Plate.
- Vinyl Protective Film Cover.
Right Fence has been machined for clearance of blade gear housing when cutting right 45-degree miters.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to setup a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or you can select a notched version below which will have the clearances needed to use your saw in the slide mode. If you have any questions or concerns, please don't hesitate to contact us! *