DeWalt 12" DW708 Zero Clearance Table Insert
Purchase 2 or more lower shipping cost
Exact fit for the DeWalt 12" Model # DW708
Made from High Density Polyethylene. Which makes it easy to make the initial cut and more durable for daily commercial use.
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
- Quick measurement of desired cut. Simply hook your tape measure into the insert and easily get an initial setting with your stop.
For a higher level of accuracy, efficiency and safety, we recommend pairing our Zero Clearance Miter Saw Plastic Insert with our Zero Clearance Fence.
DeWalt 12" DW708 EZ Speedy Zero Clearance Left and Right Fence
Purchase 2 or more product lower shipping cost
Exact fit for the DeWalt Model # DW708
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping.
- Reduce kickback.
- Reduced blade binding cutting small parts.
- Made from lightweight stable heat treated 6061-T6 Plate.
- Vinyl Protective Film Cover.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to set up a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or you can select a notched version below which will have the clearances needed to use your saw in the slide mode. If you have any questions or concerns, please don't hesitate to contact us! *
Miter Saw to DeWalt Stand - Spacer Mounting Kit
1 847 623-7029
Lead time 1 week
Mount just about ANY BRAND miter saw to the DW7231 Mounting Brackets so that you can use DeWalt DWX723, DW723, DWX724 and DWX725B stand.
Fitment is for various models, but if your miter saw is not listed in the selection below, please contact us and we can see if we have something that will work!
EZ Speedy Low Support Fence System 5' - DeWALT LEFT or RIGHT
1 847 623-7029
Made in USA
Lead Time (Made to order upon request)
Includes (1) EZ Speedy Flip-Stop , (1) EZ Speedy T-Track, (1) EZ-Speedy Table or two Roller Assemblies, (2) EZ Speedy Low Coupler Mount Assemblies and (1) Pair of EZ Speedy Fence Mount with Multi position black powder coat aluminum locking handles.
With 5 FT of material support, each EZ Speedy Low Fence can be assembled in either LEFT or RIGHT configuration as desired. Can be used for a variety of applications: Drill press, milling machine, cold saw, miter saw, radial arm saw, punch press and band saw.
This support fence system and flip stop is for the DW723, DWX723, and DWX724 DeWalt Miter Saw Stand, our EZ Speedy Fence slides right into the T-track and quickly locks down to the stand with our patent EZ Speedy Mounts.
The EZ Speedy Low Fence has multiple points of adjustment to set the height, depth, lateral position, and angle of the EZ Speedy Fence.
Once the points of adjustment are set to your saw table, they are locked down so you can easily remove the EZ Speedy Fence from the DeWalt stand, put everything into your vehicle, and head out to the job site without losing your position.
EZ-Speedy Support Stand
1 847 623-7029
Even though this Support Stand was engineered for the EZ Speedy Fence this Support Stand stands on its own.
This stand has one 1/2-13 threaded through hole mounting point at the top making it easy to bolt up or down to it
The hex mount slides right off when you loosen the 1/2-13 inch bolt on the side or upgrade to the T-Knob for $6. Tighten it up to maintain rigidness.
Adjusting the Height is done by rotating the threaded 7/8-9 adjustment screw in or out to set desired height.
Height Range is 32-1/4" to 39-1/2"
This stand has claw feet at its base to handle rough surfaces easily.
Average Lead Time 1 week
EZ Speedy Dual Clip
Lead Time 1 week
1 847 623-7029
We've re-invented the average clipboard! The EZ Speedy Dual Clip!
This clipboard design was born out of necessity to have a clipboard that fits into the t-track on our mobile miter saw base. We took it one step further and created a clipboard that has two different geometrically bent ends. One for inserting and one for hooking. The Dual Clip also has two clips so you can utilize both sides.
Hooks to anything and the opposite side allows you to insert into our EZ Speedy Fence System or any type of strut rail system. You can even set your tablet down on the dual clip. It can even work like a sturdy writing surface. Carry with you from jobsite to jobsite.
See our product video below!
EZ-Speedy T-Track ; 13/16" x 1-5/8" x 60"
The EZ-Speedy T-track can be resets flush or surface mount for your custom miter saw and table saw sled/jig set up. The EZ-Speedy T-Track can be used for precision drilling on drill press and milling machines. Buy the single T-Track to make a custom set up on one of your machines using the EZ Speedy Flip Stop
Stranded length T-Track is 60". Call or email for Custom length T-Track for you system.
Average Lead Time 1 week
Mending Plate
847-623-7029
Lead Time 1 week
Buy a single Mending Plate assembly to build a custom fence setup using our Strut Rails and Rollers. This is the same Mending Plate assembly that comes with the EZ Speedy Extension.
EZ Speedy Quick Handle (Various Thread Lengths)
847-623-7029
Lead Time 1 week
CFS has developed a heavy duty version of your typical "Vise" or "C-clamp" style handle. Intended to be used to replace any 1/2 - 13 bolt on our products where applicable.
We've recognized a need to have a quality, affordable, tooless-operated fastener to provide a simple solution to most adjustment points of nearly any product suitable - including our own. We've engineered our solution to last. You won't find any brittle plastic on our design.
Description & Features:
- Replaces Any 1/2" - 13 Bolt to be Able to Adjust With Our Tooless Alternative
- Any friction pressure point adjusted product that has a 1/2"-13 thread pitch
- High Quality Machined steel construction. All zinc plated to resist corrosion.
- Comfortable and smooth operation
- Made in America
- Available in a variety of thread lengths including a custom lengths to accommodate any project you may have.
Please do not hesitate to contact us if you have any questions.
Specification:
Main Body Dimensions: 1/2" - 13 Thread, 3/4" OD x 1-1/2" L
Handle Dimensions: 1/4" - 20 Thread 3/8" OD x 3-1/4" L
*We can make any custom length projection up to 4" long.
*Contact us for bulk pricing
EZ Speedy Dolly
Lead time 1 week
Made in the USA
Maybe you already have our EZ speedy fence? You might have extensions too? Well the EZ speedy dolly can be your solution to storing and maneuvering your fences from jobsite to jobsite.
Holds 20 feet of EZ Speedy Fence material support in an easy to maneuver compact package.
Designed with strength & durability in mind. All steel construction. Zinc plated to resist corrosion for use in all weather conditions.
Possible Configurations:
- Holds 2 EZ Speedy Fences, 2 EZ Speedy Extensions, 3 Support Stands, and up to 6 Flip-Away Strut Stops.
- Holds 1 EZ Speedy Fence, 3 EZ Speedy Extensions, 3 Support Stands, and up to 6 Flip-Away Strut Stops.
- Hold 4 EZ Speedy Extensions, 4 Support Stands, and up to 6 Flip-Away Strut Stops.
Hex Mount Assembly
Hex mount assembly for the extension fence. Allows you to mount the fence to the support stand.