EZ Speedy Handle Kit
1 847 623-7029
Lead Time 1 week
Upgrade your existing EZ Speedy Axle/Kickstand Kit with the familiar feel of our EZ Speedy Handle!
Introducing the EZ Speedy Handle Kit. Allows for greater control of your stand if you've already have our axle/kickstand kit installed. This Handle kit mounts directly onto the opposite end of your DeWalt DW723, DWX723, and DWX724 miter saw stand.
Note the DeWalt DW723 Handle Kit does not come with spacer!
Make sure that you check your model #
- Increase the mobility of your saw station.
- Leave your saw on the stand, drop the wheels to the ground, and then roll. No more lifting your saw around the job site or shop
- Save your back!
- Familiar, Comparable to operating a Hand Truck or Dolly
Comes with all necessary hardware to bolt the Handle to the stand.
Includes a template that you can tape to your saw stand to align the Handle before drilling. See our Youtube Video by scrolling below.
EZ Speedy Axle Kit
1 847 623-7029
Lead Time 1 week
Introducing the EZ Speedy Axle Kit.
This axle kit mounts directly onto your DeWalt DW723, DWX723, and DWX724 miter saw stand.
Note the DeWalt DW723 Axle Kit does not come with spacer!
Make sure that you check your model number.
- Increase the mobility of your saw station.
- Leave your saw on the stand, drop the wheels to the ground, and then roll. No more lifting your saw around the job site or shop
- Save your back!
- For save operation of Axle Kit, you must maintain proper tire air pressure.
Comes with all necessary hardware to bolt the axle to the stand and tires to the axle.
Includes a template that you can tape to your saw stand to align the axle before drilling. See our Youtube Video by scrolling below.
If you order the Axle Kit with tires, we will Ship your Kit with tires . However if you decide to order without tires we've attached the link below.
EZ Speedy Kickstand KIT
Only a few left!
1 847 623-7029
Lead Time 1 week
NOW WITH STANDARD TOOL LESS OPERATION!
EZ Speedy Kickstand KIT comes as pictured. Axle not included and is available in a separate listing below. Our kickstand mounts onto our EZ Speedy Axle Kit for the DeWalt DW723, DWX723, and DWX724 miter saw stands.
Allows the saw stand to be positioned vertically while the saw is still attached for a reduced footprint.
Rotates out of the way when not in use.
Comes with all necessary hardware to install the kickstand onto the axle. (3/16 Allen Wrench Needed to Install Cross Bar)
EZ Speedy Low Support Fence System 5' - DeWALT LEFT or RIGHT
1 847 623-7029
Made in USA
Lead Time (Made to order upon request)
Includes (1) EZ Speedy Flip-Stop , (1) EZ Speedy T-Track, (1) EZ-Speedy Table or two Roller Assemblies, (2) EZ Speedy Low Coupler Mount Assemblies and (1) Pair of EZ Speedy Fence Mount with Multi position black powder coat aluminum locking handles.
With 5 FT of material support, each EZ Speedy Low Fence can be assembled in either LEFT or RIGHT configuration as desired. Can be used for a variety of applications: Drill press, milling machine, cold saw, miter saw, radial arm saw, punch press and band saw.
This support fence system and flip stop is for the DW723, DWX723, and DWX724 DeWalt Miter Saw Stand, our EZ Speedy Fence slides right into the T-track and quickly locks down to the stand with our patent EZ Speedy Mounts.
The EZ Speedy Low Fence has multiple points of adjustment to set the height, depth, lateral position, and angle of the EZ Speedy Fence.
Once the points of adjustment are set to your saw table, they are locked down so you can easily remove the EZ Speedy Fence from the DeWalt stand, put everything into your vehicle, and head out to the job site without losing your position.
EZ Speedy Dual Clip
Lead Time 1 week
1 847 623-7029
We've re-invented the average clipboard! The EZ Speedy Dual Clip!
This clipboard design was born out of necessity to have a clipboard that fits into the t-track on our mobile miter saw base. We took it one step further and created a clipboard that has two different geometrically bent ends. One for inserting and one for hooking. The Dual Clip also has two clips so you can utilize both sides.
Hooks to anything and the opposite side allows you to insert into our EZ Speedy Fence System or any type of strut rail system. You can even set your tablet down on the dual clip. It can even work like a sturdy writing surface. Carry with you from jobsite to jobsite.
See our product video below!
DeWalt DW872 or D28715 Saw Mounting Plates
1 847 623-7029
Lead Time 1 week
Stop cutting metal on the floor. This kit allows you to mount your saw onto the DeWALT Stand. This Adapter Plate is designed to mount a DeWalt DW872 or D28715 metal cutting saw to the DW7231 Quick Release mounting brackets allowing you to work off the DeWalt DWX723, DWX724, DW723 Heavy Duty Miter Saw Stand at a comfortable working height you are used to. This also allows wood and steel cutting to be performed in the same location if desired.
Don't have a DeWalt saw? Contact us to inquire about your specific saw. The hole placements can be easily modified.
Miter Saw to DeWalt Stand - Spacer Mounting Kit
Only a few left!
1 847 623-7029
Lead time 1 week
Mount just about ANY BRAND miter saw to the DW7231 Mounting Brackets so that you can use DeWalt DWX723, DW723, DWX724 and DWX725B stand.
Fitment is for various models, but if your miter saw is not listed in the selection below, please contact us and we can see if we have something that will work!
EZ Speedy Quick Handle (Various Thread Lengths)
847-623-7029
Lead Time 1 week
CFS has developed a heavy duty version of your typical "Vise" or "C-clamp" style handle. Intended to be used to replace any 1/2 - 13 bolt on our products where applicable.
We've recognized a need to have a quality, affordable, tooless-operated fastener to provide a simple solution to most adjustment points of nearly any product suitable - including our own. We've engineered our solution to last. You won't find any brittle plastic on our design.
Description & Features:
- Replaces Any 1/2" - 13 Bolt to be Able to Adjust With Our Tooless Alternative
- Any friction pressure point adjusted product that has a 1/2"-13 thread pitch
- High Quality Machined steel construction. All zinc plated to resist corrosion.
- Comfortable and smooth operation
- Made in America
- Available in a variety of thread lengths including a custom lengths to accommodate any project you may have.
Please do not hesitate to contact us if you have any questions.
Specification:
Main Body Dimensions: 1/2" - 13 Thread, 3/4" OD x 1-1/2" L
Handle Dimensions: 1/4" - 20 Thread 3/8" OD x 3-1/4" L
*We can make any custom length projection up to 4" long.
*Contact us for bulk pricing
Hercules Miter Saw to Hercules Stand - Spacer Mounting Kit
1 847 623-7029
Lead time 1 week
Designed for mounting Hercules Miter Saw Model # HE74 to the Hercules Stand Model # HA71
We know that if you have the Hercules saw and stand that you purchase, our kit will remedy the mounting problem. The hercules miter saw has rubber feet which give the saw the ability to not stretch what your setting the saw on. They also prevent the saw from shifting or sliding in use. The problem you run into when you attempt to bolt the saw base down to the hercules mounting brackets is that the mounting brackets will bolt up crooked and you end up deforming the brackets and you will warp the saw base. Our spacer kit will allow you to mount using the included bolts included when you purchase the stand.