RIDGID 10" R4241 EZ Speedy Zero Clearance Left and Right Fence
Purchase 2 or more product lower shipping cost
Exact fit for the RIDGID 10" R4241
If you are looking to increase the safety and precision of your cuts then our Zero Clearance Fence is the perfect product for you. No more small pieces jamming into your standard fence and binding your blade.
- Increase product cutting support.
- Reduce chipping.
- Reduce kickback.
- Reduced blade binding cutting small parts.
- Made from lightweight stable heat treated 6061-T6 Plate.
- Vinyl Protective Film Cover.
Right Fence has been machined for clearance of blade gear housing when cutting right 45-degree miters.
We also put a relief cut on the inside edges of the aluminum fence. This will allow you to change the angle of your saw while still being able to accurately hook your tape measure onto the fence edge. Enabling you to set up a miter cut as quickly and accurately as a 90-degree cut.
The two aluminum fence pieces come shipped with flat head bolts + flange nuts.
For greater accuracy, efficiency and safety, we recommend pairing our Zero Clearance Fence with our Zero Clearance Table Insert.
*Please note these fences were engineered to allow for zero clearance material support at the highest vertical cutting capacity which is achieved in what is commonly referred to as "Chop Mode”, therefore you cannot operate this specific saw in the slide mode without hitting the fences. If you desire the ability to use in the slide mode, you just slide the fences out of the way so that you don't hit, or you can select a notched version below which will have the clearances needed to use your saw in the slide mode. If you have any questions or concerns, please don't hesitate to contact us! *
RIDGID 10" R4241 Zero Clearance Table Insert
Purchase 2 or more lower shipping cost
Buy 3 and get 1 Free you save 25%
1 847 623-7029
Exact fit for the RIDGID 10" R4241
Made from High Density Polyethylene. Which makes it easy to make the initial cut and even more durable for daily commercial use.
- Machined out of solid Density Polyethylene Sheet
- Increase product cutting support.
- Reduce chipping
- Reduce kickback
- Reduced blade binding cutting small parts.
- Quick measurement of desired cut. Simply hook your tape measure into the insert and easily get an initial setting with your stop.
For a higher level of accuracy, efficiency and safety, we recommend pairing our Zero Clearance Miter Saw Plastic Insert with our Zero Clearance Fence.
1 NEW DeWalt DWX724 Stand Drilled for Axle and Handle Kit
1 847 623-7029
Lead Time 1 week
Introducing the new Predrilled miter saw stand
1 NEW DeWalt DWX724 Stand Drilled for Axle, Kickstand and Handle Kit. Accessories not included.
EZ Speedy Axle Kit
1 847 623-7029
Lead Time 1 week
Introducing the EZ Speedy Axle Kit.
This axle kit mounts directly onto your DeWalt DW723, DWX723, and DWX724 miter saw stand.
Note the DeWalt DW723 Axle Kit does not come with spacer!
Make sure that you check your model number.
Increase the mobility of your saw station.
- Leave your saw on the stand, drop the wheels to the ground, and then roll. No more lifting your saw around the job site or shop
- Save your back!
- For safe operation of Axle Kit, you must maintain proper tire air pressure.
- New Chrome Plating for lifetime finish
Comes with all necessary hardware to bolt the axle to the stand and tires to the axle.
Includes a template that you can tape to your saw stand to align the axle before drilling. See our Youtube Video by scrolling below.
If you order the Axle Kit with tires, we will Ship your Kit with tires .
EZ Speedy Kickstand Kit
1 847 623-7029
Lead Time 1 week
NOW WITH STANDARD TOOL LESS OPERATION!
EZ Speedy Kickstand KIT comes as pictured. Axle not included and is available in a separate listing below. Our kickstand mounts onto our EZ Speedy Axle Kit for the DeWalt DW723, DWX723, and DWX724 miter saw stands.
Allows the saw stand to be positioned vertically while the saw is still attached for a reduced footprint.
Rotates out of the way when not in use.
Comes with all necessary hardware to install the kickstand onto the axle. (3/16 Allen Wrench Needed to Install Cross Bar)
- New Chrome Plating for lifetime finish
EZ Speedy Handle Kit
1 847 623-7029
Lead Time 1 week
Upgrade your existing EZ Speedy Axle/Kickstand Kit with the familiar feel of our EZ Speedy Handle!
Introducing the EZ Speedy Handle Kit. Allows for greater control of your stand if you've already have our axle/kickstand kit installed. This Handle kit mounts directly onto the opposite end of your DeWalt DW723, DWX723, and DWX724 miter saw stand.
Note the DeWalt DW723 Handle Kit does not come with spacer!
Make sure that you check your model #
- Increase the mobility of your saw station.
- Leave your saw on the stand, drop the wheels to the ground, and then roll. No more lifting your saw around the job site or shop
- Save your back!
- Familiar, Comparable to operating a Hand Truck or Dolly
Comes with all necessary hardware to bolt the Handle to the stand.
Includes a template that you can tape to your saw stand to align the Handle before drilling. See our Youtube Video by scrolling below.
EZ Speedy New Low Support Fence System 5' - DEWALT LEFT or RIGHT
1 847 623-7029
Made in USA
Lead Time (Made to order upon request)
Includes only (1) Side
What you get is (1) EZ Speedy Flip-Stop , (1) EZ Speedy T-Track, (1) EZ-Speedy Table (2) EZ Speedy Low Coupler Mount Assemblies and (1) Pair of EZ Speedy Fence Mount with Multi position black aluminum locking handles.
With 5 FT of material support, each EZ Speedy Low Fence can be assembled in either LEFT or RIGHT configuration as desired. Can be used for a variety of applications: Drill press, milling machine, cold saw, miter saw, radial arm saw, punch press and band saw.
This support fence system and flip stop is for the DW723, DWX723, and DWX724 DEWALT Miter Saw Stand, our EZ Speedy Fence slides right into the T-track and quickly locks down to the stand with our patent EZ Speedy Mounts.
The EZ Speedy Low Fence has multiple points of adjustment to set the height, depth, lateral position, and angle of the EZ Speedy Fence.
Once the points of adjustment are set to your saw table, they are locked down so you can easily remove the EZ Speedy Fence from the DEWALT stand, put everything into your vehicle, and head out to the job site without losing your position.
EZ Speedy Dual Clip
Lead Time 1 week
1 847 623-7029
We've re-invented the average clipboard! The EZ Speedy Dual Clip!
This clipboard design was born out of necessity to have a clipboard that fits into the t-track on our mobile miter saw base. We took it one step further and created a clipboard that has two different geometrically bent ends. One for inserting and one for hooking. The Dual Clip also has two clips so you can utilize both sides.
Hooks to anything and the opposite side allows you to insert into our EZ Speedy Fence System or any type of strut rail system. You can even set your tablet down on the dual clip. It can even work like a sturdy writing surface. Carry with you from jobsite to jobsite.
See our product video below!